To change glow plugs, you typically need a correctly sized deep socket, ratchet, socket extensions, an accurate low-range torque wrench, basic hand tools for removing engine covers or intake parts, and a multimeter if you want to test the glow plugs before replacing them. Depending on the diesel engine, you may also need penetrating fluid, compressed air or a vacuum for cleaning the plug area, a glow plug connector removal tool, a thread-cleaning tool, or a specialized extractor if a plug is seized or broken.
The exact tool list varies considerably between engines. On some diesels, the glow plugs sit in an accessible row and can be replaced with a socket and ratchet. On others, the intake manifold, fuel-system components, engine covers, or electrical harnesses must be moved before you can even reach them.
Glow plugs also require more care than many ordinary fasteners. They are long, relatively thin components threaded into the cylinder head. If one has been installed for years, carbon and corrosion can make it difficult to remove. Excessive torque can snap the plug and turn a simple replacement into a specialized extraction job.
That is why having the correct tools—and knowing which tools not to use—is important.
In this guide, I’ll explain what tools you need to change glow plugs, which tools are essential versus optional, how socket size varies, why a torque wrench matters, what you need for seized plugs, and how to prepare before starting the job.
Basic Tools Needed to Change Glow Plugs

For a straightforward glow plug replacement, you will usually need only a modest set of hand tools.
The core tools are:
- Correct deep socket
- Ratchet
- Socket extensions
- Torque wrench
- Screwdrivers or small sockets for covers and brackets
- Multimeter for testing
- Cleaning equipment
The challenge is making sure each tool is appropriate for the particular engine.
Deep Socket
A deep socket is usually the most important tool.
Glow plugs typically extend above the cylinder head far enough that a shallow socket cannot reach the hex correctly.
The socket size varies by glow plug design.
Common glow plug hex sizes may include 8 mm, 9 mm, 10 mm, 12 mm, or other sizes depending on the engine.
Do not assume every diesel uses the same glow plug socket.
Use the exact size that fits the hex snugly.
A loose socket can round the glow plug and make removal much more difficult.
Ratchet
A small ratchet is usually better than a long breaker bar for normal glow plug work.
A 1/4-inch-drive ratchet is often useful because many glow plugs are small and do not require large removal torque when everything is functioning normally.
A 3/8-inch-drive ratchet may also be appropriate depending on socket size and access.
The advantage of a smaller ratchet is feel.
You can sense resistance more easily and are less likely to apply excessive torque without realizing it.
Socket Extensions
Extensions are frequently necessary because glow plugs often sit deep in the cylinder head or beneath intake components.
A combination of short and medium-length extensions is useful.
Try to keep the socket and extension aligned as straight as possible with the glow plug.
Side-loading the plug while loosening it can increase the chance of bending or breaking it.
Torque Wrench
A torque wrench is one tool I strongly recommend.
Glow plugs generally require relatively low installation torque.
Overtightening can:
Damage the glow plug, stretch its body, damage cylinder-head threads, or make future removal much more difficult.
Use a torque wrench whose operating range includes the specified glow plug torque near the middle of its scale.
A large automotive torque wrench designed for wheel lug nuts may not be accurate enough at the very low values used for small glow plugs.
Key Takeaways:
- The most important tools are the correct deep socket, ratchet, extensions, and low-range torque wrench.
- Glow plug socket size varies by engine.
- A smaller ratchet gives better feedback and reduces the temptation to apply excessive force.
What Size Socket Do You Need for Glow Plugs?
There is no universal glow plug socket size.
The correct size depends on the glow plug manufacturer and engine design.
Some glow plugs use a small hex such as 8 mm or 10 mm, while others are larger.
The safest approach is to identify the glow plug part number or consult service information before buying a socket.
Why Fit Matters
Glow plugs can become tight after years of heat cycles.
If you use a poorly fitting socket, the corners of the hex can round off.
Once rounded, the glow plug may require gripping tools or an extractor.
That makes an already delicate job considerably more difficult.
Standard Deep Socket vs. Glow Plug Socket
A normal deep socket may work perfectly if access is good.
Special glow plug sockets sometimes include features such as:
Magnetic retainers, rubber inserts, swivel sections, or narrow outside diameters.
These features can be useful in deep or tight cylinder-head passages.
However, a specialized socket is not mandatory for every engine.
Do You Need a Special Glow Plug Socket?
Not always.
If a standard quality deep socket fits the glow plug correctly and can access the plug without binding against surrounding parts, it may be all you need.
A dedicated glow plug socket becomes more valuable when the plugs are:
Very deep in the cylinder head, installed at an angle, located in a narrow bore, or difficult to retrieve after unthreading.
Magnetic Glow Plug Sockets
A magnetic socket can hold the glow plug after it has been completely unscrewed.
This makes it easier to lift the plug out of a deep bore.
It can also hold the new plug during installation.
This reduces the chance of dropping it into a difficult location.
Swivel Glow Plug Sockets
Some sockets have a built-in swivel joint.
These help where the glow plug sits at an angle.
Use swivels carefully.
A large angle can make it harder to apply torque directly along the glow plug’s axis.
Whenever possible, straight access is preferable.
Do You Need a Torque Wrench for Glow Plugs?
You can physically install glow plugs without one, but I recommend using a torque wrench whenever possible.
Glow plugs are usually threaded into aluminum cylinder heads and are relatively slender.
The difference between properly tightened and overtightened may not feel large by hand.
Why Overtightening Is Dangerous
Excessive torque can stretch the glow plug.
It may also distort the sealing area or damage the cylinder-head threads.
A plug installed too tightly may become extremely difficult to remove later.
In severe cases, it can snap during future service.
Why Undertightening Is Also a Problem
A loose glow plug may not seal correctly.
Combustion pressure can leak around the plug.
This may produce:
A ticking or puffing sound, carbon buildup around the plug, and possible thread damage over time.
Use the exact torque specification for your engine and plug.
There is no universal glow plug torque value.
Do You Need a Multimeter?
A multimeter is not strictly required if you are replacing glow plugs that have already been properly diagnosed.
However, it is one of the most useful tools to have.
Before replacing the plugs, you can test them and determine whether they are actually faulty.
Resistance Testing
A digital multimeter can measure the resistance of each glow plug.
Glow plugs generally have very low resistance.
A completely open plug may show OL or infinite resistance.
That typically indicates a failed internal heating element.
Compare the Plugs
Because resistance can be extremely low, comparing all cylinders can be helpful.
If most plugs show similar readings and one is dramatically different, that plug deserves attention.
Always use the manufacturer specification when available.
Multimeter Lead Resistance
Touch the two meter probes together before testing.
The reading you see is the resistance of the leads themselves.
Because glow plug resistance may be close to 1 ohm or less, this small amount can materially affect your result.
Key Takeaways:
- A torque wrench helps prevent both over- and under-tightening.
- A multimeter lets you confirm that the plugs actually need replacement.
- Use vehicle-specific resistance and torque specifications whenever possible.
What Basic Hand Tools Might You Need?
Glow plug access varies greatly.
Even if removing the glow plugs themselves requires only one socket, you may need other tools to remove surrounding parts.
Common examples include:
Screwdrivers, Torx bits, Allen bits, small metric sockets, pliers, hose-clamp pliers, and trim tools.
Engine Covers
Many modern diesels have large plastic engine covers.
Some pull upward from rubber mounts.
Others are held with screws or bolts.
Do not force a cover until you know how it is attached.
Intake Components
On certain engines, intake pipes or the intake manifold may block the glow plugs.
Removing these components can require Torx or E-Torx sockets, conventional metric sockets, and extensions.
If the intake manifold is removed, new gaskets may be required during reassembly.
Electrical Connectors
Glow plugs may have individual push-on connectors, threaded terminals, or a shared electrical bus bar.
Small pliers or a dedicated connector tool can help, but be careful.
Old diesel-engine wiring can become brittle from heat.
Do You Need a Glow Plug Connector Removal Tool?
Sometimes.
Many glow plug connectors can be removed carefully by hand.
Others are deeply recessed or difficult to grip.
A dedicated glow plug connector puller can remove the connector more evenly and reduce the risk of damaging the wire.
This tool is particularly useful when working on older European diesels where the glow plug harness connectors sit tightly over the plug terminals.
Avoid Pulling on the Wire
Pull on the connector body rather than the wire.
Yanking the wire can damage the conductor internally or separate it from the terminal.
A damaged connector can create the same symptoms as a failed glow plug.
What Cleaning Tools Do You Need?
Cleaning before glow plug removal is important.
Once the plug is removed, the bore provides a path toward the combustion chamber.
You do not want loose dirt or debris falling into the engine.
Vacuum
A small workshop vacuum with a narrow nozzle is useful for removing loose dirt around the glow plug.
This is often one of the safest approaches because debris is pulled away rather than blown around.
Compressed Air
Compressed air can also clean the area.
Wear eye protection.
Use controlled air pressure and keep your face away from the debris path.
If the plug sits in a deep bore, make sure dirt does not simply get pushed deeper.
Brushes
A small soft or nylon brush can loosen surface dirt before vacuuming.
Avoid aggressive wire brushing around open engine passages where metal fragments could become contamination.
Do You Need Penetrating Oil?
Maybe.
If the glow plugs are old or known to seize in that particular engine, a suitable penetrant can sometimes help loosen corrosion around the threads.
However, it is not mandatory for every replacement.
When It Can Help
Penetrant is most useful when:
The plug initially feels unusually tight, corrosion is visible, or the engine has a reputation for seized glow plugs.
Apply a small controlled amount around the base of the plug if the service procedure allows it.
Give it time to work.
What Penetrating Oil Cannot Fix
Penetrant may not solve a plug that is trapped by heavy carbon around its heating tip.
That carbon is located on the combustion side of the cylinder head.
A plug can therefore unthread normally but still refuse to pull out.
Specialized carbon-cleaning tools may be needed in that situation.
Do You Need a Breaker Bar?
Usually no.
A breaker bar is generally not one of the tools I would reach for first when changing glow plugs.
Its long handle allows you to apply very high torque.
That is useful for large seized bolts but risky for a thin glow plug.
Why a Small Ratchet Is Better
A small ratchet gives you feedback.
If the glow plug begins twisting or binding, you are more likely to feel it.
With a long breaker bar, you can exceed the plug’s breaking strength before realizing how much torque you have applied.
If a glow plug does not loosen with controlled force, use the manufacturer-specific seized-plug procedure rather than simply increasing leverage.
Do You Need an Impact Wrench?
Generally, no.
A conventional impact wrench is not recommended for normal glow plug removal.
Repeated impact force can break a seized plug and gives you little feedback about what is happening.
Some professional shops use specialized low-force vibration tools designed specifically to help release seized glow plugs.
That is different from using a normal high-torque impact gun.
For typical DIY replacement, controlled hand tools are safer.
Tools for a Seized Glow Plug
If a glow plug is seized, the tool list can become more specialized.
Useful equipment may include:
A low-range torque wrench for monitoring removal force, penetrating fluid, specialized vibration tool, carbon reamer, glow plug extractor kit, and thread repair equipment.
However, not every seized plug should be treated as a DIY extraction job.
Carbon Reamer
A glow plug bore reamer is designed to remove carbon deposits from the bore.
It can be useful when the engine manufacturer specifies cleaning after plug removal.
The reamer must be the correct size for the engine.
Using the wrong diameter or depth can damage the cylinder head.
Some procedures require grease on the reamer to capture carbon debris.
Follow the tool and engine manufacturer’s procedure.
Glow Plug Extractor Kit
An extractor kit becomes useful if the glow plug breaks.
These kits may include:
Drill guides, specialized drill bits, taps, pullers, threaded extraction rods, and centering adapters.
The purpose is to remove the broken glow plug while leaving the cylinder head installed whenever possible.
This is much more advanced than normal plug replacement.
Do You Need Thread-Chasing Tools?
Sometimes.
If the glow plug threads in the cylinder head are dirty or carbon-contaminated, a proper thread chaser can clean them.
A thread chaser is preferable to an ordinary cutting tap when the goal is simply to clean existing threads.
A cutting tap can remove material unnecessarily.
Keep Debris Out of the Cylinder
Any thread-cleaning operation near the combustion chamber creates a contamination risk.
Use the manufacturer-approved procedure.
Do not aggressively chase threads just because the new plug feels slightly different going in.
First verify that you have the correct plug and thread specification.
Do You Need Anti-Seize?
Do not automatically add anti-seize simply because the glow plug threads into an aluminum head.
Glow plug manufacturers may specify dry installation or a particular coating.
Lubricating threads changes friction.
That means the same torque-wrench reading can produce greater clamping force when the threads are lubricated.
This can lead to overtightening.
Follow the Plug Manufacturer
If the new glow plug is supplied with a special coating, install it as instructed.
If anti-seize is explicitly recommended, use only the specified amount and adjust torque only if the manufacturer instructs you to do so.
Do not create your own torque reduction formula.
Do You Need Dielectric Grease?
Usually not on the glow plug threads.
Dielectric grease may sometimes be appropriate for certain electrical connectors or boots, but it should not be applied indiscriminately.
Follow the vehicle or connector manufacturer’s guidance.
A clean, secure electrical terminal is more important than adding grease without knowing whether it is intended.
What Replacement Parts Should You Have Ready?
Before starting, verify that you have the correct glow plugs.
Do not select them solely by thread diameter.
Glow plugs can differ in:
- Voltage
- Length
- Tip diameter
- Heating rate
- Resistance
- Material
- Electrical control strategy
Some modern plugs are ceramic.
Others may include integrated pressure sensing.
Installing the wrong plug can cause immediate failure or damage the control system.
Gaskets and Intake Seals
If glow plug access requires removing the intake manifold or other sealed components, have replacement gaskets available.
Reusing a damaged intake gasket can create air leaks after the repair.
Should You Have a Scan Tool?
A scan tool is not essential for physically replacing glow plugs, but it is very useful on modern diesels.
It can help identify which glow plug circuit has a fault.
It may also show whether the problem is actually the glow plug control module, wiring, or another component.
Clear Codes After Repair
After replacing the failed component, a scan tool can clear stored trouble codes.
You can then restart the engine and verify that the codes do not return.
On some vehicles, the code may clear automatically after several successful drive cycles, but a scan tool makes verification much faster.
What Safety Equipment Do You Need?
At minimum, wear eye protection and suitable gloves.
Glow plug service may involve hot engine parts, compressed air, sharp components, and electrical connections.
If the manufacturer specifies working with the engine warm, take extra care around the turbocharger, exhaust manifold, EGR system, and coolant components.
Battery Safety
Some procedures require disconnecting the negative battery terminal.
If you do this, make sure you understand whether the vehicle may lose radio codes, memory settings, or require other reset procedures.
Glow plug systems can draw very high current, so avoid accidentally shorting electrical terminals with tools.
Key Takeaways:
- Cleaning and electrical diagnostic tools can make the job safer and more accurate.
- Seized or broken glow plugs may require specialized reamers and extractor kits.
- Do not automatically use anti-seize, impact tools, or large breaker bars.
Basic Glow Plug Tool Kit for DIY Replacement
For a relatively accessible diesel engine, I would want the following before starting:
A correctly sized deep socket, 1/4- or 3/8-inch ratchet, several extensions, a low-range torque wrench, screwdrivers and metric sockets, digital multimeter, shop vacuum or compressed air, eye protection, and the correct replacement glow plugs.
That covers most uncomplicated jobs.
If the engine has a reputation for plug seizure, I would also have suitable penetrating fluid available and review the removal torque procedure before touching the first plug.
Advanced Tool Kit for Difficult Glow Plug Jobs
For professional or more challenging work, the kit may expand to include:
A dedicated glow plug socket set, connector pullers, flex-head ratchets, bore-cleaning reamers, thread chasers, low-range torque adapters, current clamp, advanced scan tool, and a broken glow plug extraction kit.
Most DIY owners do not need to purchase all of these for a single routine replacement.
If the job reaches the point where drilling or extraction is required, paying a specialist can be less expensive than buying tools and risking cylinder-head damage.
How to Prepare Before Changing Glow Plugs
Good preparation can prevent many mistakes.
First, identify the exact engine code.
Then verify the correct glow plug part number.
Find the specified installation torque.
Check whether the manufacturer recommends removing plugs hot, warm, or cold.
Determine what components must be removed for access.
Finally, scan for fault codes and test the plugs before ordering parts if possible.
This prevents replacing a glow plug when the real problem is the controller or wiring.
Do You Need to Replace All Glow Plugs at Once?
Not necessarily.
If one plug fails and the others test correctly, replacing one can be reasonable.
If all plugs are old, the labor to access them is significant, and several show similar deterioration, replacing the full set may make sense.
The risk of removal matters too.
On an engine known for seized glow plugs, removing several functioning plugs purely as preventive maintenance may create more risk than benefit.
Use the engine manufacturer’s guidance and actual test results.
Can You Change Glow Plugs Yourself?
Yes, on many diesel engines.
The job can be straightforward when the plugs are easily accessible and come out normally.
The difficulty increases significantly when:
Intake components block access, electrical connectors are fragile, plugs are seized, or the engine uses expensive pressure-sensing or ceramic glow plugs.
The key skill is knowing when to stop.
A glow plug that does not behave like a normal threaded component should not simply be forced.
When Should You Let a Mechanic Change the Glow Plugs?
Professional service makes sense if a plug is heavily seized, already broken, located in a very difficult area, or requires intake and fuel-system disassembly beyond your experience.
You should also consider professional service if the engine has a known history of glow plug breakage.
A diesel technician may have specialized extraction tools that allow a seized or broken plug to be removed without taking off the cylinder head.
That can save substantial repair cost.
Common Tool Mistakes When Changing Glow Plugs
One common mistake is using the wrong socket size.
Even a small amount of looseness can round the hex.
Another is using a full-size breaker bar because the plug initially feels tight.
That can snap the plug.
Using an oversized torque wrench for installation is another problem. A tool designed for 150 lb-ft wheel nuts may not be accurate at a tiny glow plug torque value.
A fourth mistake is buying a broken-plug extractor before confirming what kind of failure you actually have.
Seized threads, carbon-bound tips, rounded hexes, and broken plugs require different tools.
Finally, do not forget diagnostic tools. A multimeter and scan tool can prevent you from replacing perfectly good plugs.
FAQs about What Tools Do I Need to Change Glow Plugs
What tools do I need to change glow plugs?
You usually need a deep socket, ratchet, socket extensions, low-range torque wrench, basic hand tools, and preferably a multimeter.
Additional tools may be needed for difficult access or seized plugs.
Do I need a special socket for glow plugs?
Not always.
A correctly sized standard deep socket can work on many engines.
Special glow plug sockets are useful for deep or angled installations.
What size socket do glow plugs use?
It varies by engine and plug design.
Common sizes may include 8 mm, 9 mm, 10 mm, and 12 mm, but you should verify the exact specification.
Do I need a torque wrench for glow plugs?
It is strongly recommended.
Glow plugs require relatively low, specific torque and can be damaged by overtightening.
Can I use a regular ratchet?
Yes.
A small ratchet is often ideal because it gives good feedback and reduces the chance of applying excessive force.
Can I use a breaker bar?
Generally, avoid one for normal removal.
If a plug needs extreme leverage, it may be seized and require a special procedure.
Can I use an impact wrench?
A standard impact wrench is not recommended for normal glow plug removal.
Controlled hand torque is safer.
Do I need a multimeter?
Not strictly, but it is very useful for confirming whether a glow plug has actually failed.
Do I need a scan tool?
Not for the physical replacement, but a scan tool can identify glow plug circuit faults and verify the repair.
Do I need penetrating oil?
Only if the plug is tight and the manufacturer-approved procedure allows it.
It may help with thread corrosion but not necessarily with carbon around the tip.
Do I need a glow plug extractor?
Only if a plug breaks or becomes severely damaged during removal.
Routine replacements do not require an extractor.
What is a glow plug reamer used for?
A reamer removes carbon from the glow plug bore.
It must be the correct size for the specific engine.
Should I use anti-seize on glow plugs?
Only if the engine or glow plug manufacturer recommends it.
Added lubricant changes tightening characteristics.
Do glow plugs need dielectric grease?
Usually not on the threads.
Use electrical grease only where the vehicle or component manufacturer specifies it.
Can I change glow plugs without disconnecting the battery?
Some procedures may allow it, while others require battery disconnection.
Follow the service instructions for your vehicle.
Can I change glow plugs with the engine hot?
Some engines specify warm removal, while others have different requirements.
Use the procedure for your exact engine.
What happens if a glow plug breaks?
A specialized extraction kit may be needed to remove the remaining portion from the cylinder head.
Can a broken glow plug be removed without taking off the head?
Often, yes, with professional extraction tools.
It depends on where the plug broke.
Should I replace all glow plugs together?
Not necessarily.
Test the remaining plugs and consider age, mileage, access, and manufacturer recommendations.
Can I use pliers to remove a glow plug?
Pliers are not appropriate for normal threaded removal.
Use the correct socket.
Special gripping tools may only be useful after the hex has already been damaged.
Is changing glow plugs difficult?
It can range from very easy to highly difficult depending on access and whether the plugs are seized.
Conclusion
So, what tools do I need to change glow plugs? For most routine jobs, start with a correctly sized deep socket, a small ratchet, several socket extensions, an accurate low-range torque wrench, and basic hand tools for removing any covers or intake components that block access.
A digital multimeter is also extremely useful because it allows you to test the glow plugs before replacing them. On a modern diesel, a scan tool can further help identify whether the actual fault is the plug, wiring, relay, or glow plug control module.
Cleaning tools such as a shop vacuum, compressed air, and a small brush help keep debris out of the glow plug bore.
If the plugs are old or difficult to remove, suitable penetrating fluid and engine-specific removal information become especially important.
For seized or broken plugs, specialized equipment may be necessary, including a glow plug bore reamer, connector puller, thread chaser, or dedicated broken glow plug extraction kit.
What you generally should not rely on is a large breaker bar or standard impact wrench. Glow plugs are thin and can snap if excessive force is applied.
The best tool list therefore depends on the job: for a normal replacement, use precision hand tools and a torque wrench; for a seized plug, use specialized tools and controlled removal methods rather than more force.
Before starting, verify the exact glow plug socket size, removal procedure, installation torque, and engine-temperature recommendation for your particular diesel. That preparation is one of the best tools you can have for completing the job without damaging the glow plug or cylinder head.
